Lamp EVO LED 12/24 Red magnet

Description:

The flashing light EVO LED T1 category is the source of the warning light for emergency or specialized vehicles in road traffic. The lamp is made in three different colors of light: blue, red and yellow car. Components and technical solutions applied to the lamp ensure a long, efficient, energy-efficient and trouble-free operation of the lamp.

Technical data

Supply voltage: 12V and 24 V car installation

Power consumption: approx. 15W

Recommended fuse protection: 5A

Flash frequency: 2-4 Hz

Operating temperature range: -30 ° C - + 50 ° C

Light source: 16 x 1W LED + dedicated optics

Flash synchronization: via synchronization cable

Synchronization of several (up to ten) lamps can be obtained by combining yellow synchronization cables of these lamps. It is also possible to obtain alternating synchronization. Switching of the synchronization mode should be performed according to the following procedure:

- attach the lamp power to start work,

- attach the synchronization cable to to the positive power supply (white cable) for a little longer than 1 second, the lamp is not flashing at that time,

- switching of the synchronization mode switch for the alternate one is signalled by one short flash, after which you should immediately disconnect the synchronization cable from the positive poer supply (holding the cable for too long results in failure of the operation),

- disconnect and reconnect the power supply, the lamp properly switched to the alternate flash at the beginning of its work has approx. two-second flashing pause - returning to the original operating mode is by attaching the synchronization cable to the positive power supply for approx. 5 seconds (the lamp is not flashing at thas time) and the immediate disconnection after the next, short confirming flash.

It is recommended to secure (insulate) the yellow cable when the synchronication is not used in order to avoid any interference in the lamp operation.

NOTE: The lamp is designed to operate with a supply from the vehicle installation. Using other power supplies is permitted, provided that you meet the appropriate power parameters: 10V..15V / 5A or 20V..30V / 3A. Exceeding these parameters may damage the lamp and void the warranty.

Marking of cables and connection of the lamp:

BROWN - "+" car installation

WHITE - "-" car installation

YELLOW - SYNCHRONIZATION function

INSTALLATION AND USE OF EVO LED WARNING LAMP

1. COMPONENTS

The lamp is provided as a mechanical element including emitting devices with control and supply system in a housing with transpatent lampshade.  The cable from the body is led out in the tyre and supplies power and control signals to the lamp.

The device is suitable for automotive installations with 12V and 24V rated voltage.

2. LOCATION AND INSTALLATION OF THE LAMP.

The EVO LED lamp is designed for installation on a vehicle directly on its roof.  The installation place should ensure the horizontal position of the lamp (the surface parallel to the ground on which the vehicle stands). The lamp should be installed with the use of accessories supplied by the manufacturer, with ensuring that this is done in a stable and reliable manner. Electrical cables should be led out and fixed in a manner not exposing   them to abrasion, fracture, rupture and, consequently, to short-circuit.

Note: Failure to observe the foregoing, may result in a fire of vehicle installation!

3. COMMENTS ON THE ELECTRICAL INSTALLATION.

The devices should be installed only by persons qualified in fixing electrical installations in motor vehicles. The installation should be carried out in accordance with the instruction provided by the manufacturer, with using appropriate tools. The manufacturer is not  responsible for installation errors and their consequences.  

It is recommended to equip the power of the lamp with a circuit breaker rated at 5A.

You should use appropriate tools and materials for installation. You shoud use  power cables of the appropriate cross-section (1 mm2 is recommended). Using long cables of too small cross-sections may result in large voltage drops and prevent from proper operation of the lamp.

You should connect the power and controls for the lamp switching on/off  by connecting the cable led out from the lamp to the relevant installation points of the vehicle, as described in the Table.

4. ELECTRICAL CONNECTION.

The power cable must include an instantenous fuse of rated current of 5A and an operating voltage of 32V incorporated in the circuit.  

Note: You should not connect the lamp to the power supply voltage and without the proper fuse. Failure to follow these instructions may result in damage  of the equipment and even in a vehicle fire!

The manufacturer may refuse the warranty repair in case of unsuitable powering of the lamp.

You should pay special attention to the correct connection of the positive (+) and the (-) power supply. The replacement of power cables may result in damage of  the lamp and be the grounds for refusing the warranty repair.

Connecting of the EVO LED warning lamp connections cable.

White cable – minus power „-” - the mass of the vehicle installation

Brown cable - plus power „+" of vehicle installation by a switch

Yellow cable – the line of lamps synchronization similar to the line of another lamp

5. CHARGING THE VEHICLE BATTERY.

If it is necessary to recharge the vehicle's battery from an external source (a Booster, a charger, another battery), it is recommended to avoid switching on the lamp during charging. Using inapproppriate chargers with the connected lamp can damage it and void the warranty.

Warranty card and montage instruction - download in SERVICE.

We have in offer:

- Amber cover Amber light 1point montage (index 04.751)
- Amber cover Amber light magnetic montage (index 04.761)
- Red cover Red light 1point montage (index 04.801),
- Red cover Red light magnetic montage (index 04.811),
- Blue cover Blue light 1point montage (index 04.851),
- Blue cover Blue light magnetic montage (index 04.861),
and with clear glasses

- Clear cover Amber light 1point montage (index 04.771)
- Clear cover Amber light magnetic montage (index 04.781)
- Clear cover Red light 1point montage (index 04.821),
- Clear cover Red light magnetic montage (index 04.831),
- Clear cover Blue light 1point montage (index 04.871),
- Clear cover Blue light magnetic montage (index 04.881).


In order: Yes

Height 57 mm, diameter 148 mm